Henry Taylor Tools Ltd. Henry Taylor Tools Ltd.  
contact home page  
see our range designed by experts  
Amateur & Professional
Sculpture Tools
Carving Tool Sets
Selected Sets
Micro Carving Tools
Turning Tools Introduction & Sets
Gouges
Chisels
Scrapers
Beading Tools
Parting Tools
HSS Turning Tools 1
HSS Turning Tools 2
HSS Turning Tools 3
Supertip 2000
Woodworking Chisels

  HSS Woodturning Tools Page 3


The following Tools have been developed in cooperation with international expert Ray Key.

 

A. 'Key Parting Tool HSS. Section 1/2" X 3/32"
Used with the widest width of the tool down on the rest, the tapered section gives tool clearance
and stops binding. HS107

B & C 'Key' French Curve Scrapers HSS. Section 11/2" X 3/8" for larger work 1" X 1/4"
for smaller work. The shape of the tool makes it easy to remove any ripples and undulations from the bowl gouge. Blending of curves is easy and outward side pressure on the walls of bowls is virtually eliminated when the tool is used correctly. (Side pressure can cause wood to flex and give a catch or dig in and shatter.) HS108 & HS109

 

 

D. 'Key' Round Cutaway Scraper HSS. Section 3/4" X 1/4"
For inside work with small openings the cut away section allows easier manipulation under any shoulder and minimises the chance of fouling the tool on the far side of the opening. HS110

E. 'Key' Shear Scraper HSS.
Section 11/2" X 5/16"
The stubby, heavy section and rounded edges make for easy use and damps down vibration. Used at an angle of 30° to 45° out of the horizontal, gives a fine finish on difficult timbers when used in this way, for bowls and flat work. HS111

 Diamic Brand Tools

 

 

 

 

Supertip 2000

The ultimate bowl turning & hollowing tool

Many tips are available...
all are made from 16mm round bar M2 HSS 

 Supertip 2000
   
Supertip 2000
Straight Gouge -
Superflute profile

Performs exactly as the original Superflute
for general and heavy duty bowl turning. 		Supertip 2000
 Straight Gouge -
"U" shape flute profile

With a larger radius at the bottom of the flute.
Preferred by many turners for grinding back special "pointed" shapes. 		Supertip 2000
Loop Hollowing Tool
This works like a ring tool but has superior clearance for shavings and, because it has a smaller working radius, it is much easier to control. Gives an excellent finish and can hollow into deep and awkward places where a ring tool could not reach. Also good for deep straight sided hollows. It has two cutting edges with different bevel angles. 		Supertip 2000 Angled Gouge -
"U" shape flute profile
This tip produces a much superior finish inside a bowl - even a deep bowl. Easier to get a smooth flowing interior curve without steps in the shape. The handle can be used horizontal so a pivoting head lathe is not needed for good results. 		Supertip 2000
Pointed nose style also available.

Tips just screw in.No grub screws to clog. No special tools needed. Tips can be freely interchanged or replaced when worn. Tool stays virtually full length in use. Shank is stronger and more rigid than a conventional gouge. Shank cannot snap. Extra long shanks available. Tip is flush with the shank - nothing to catch on the tool rest. Tips are easy to sharpen on conventional equipment and keep an extra keen edge. Tool is just
as easy to use and
gives a superior finish.

more than 150 years of craftsmanship

HOME -- AMATEUR & PROFESSIONAL -- SCULPTURE TOOLS -- UNSHOULDERED PRINT & BLOCKCUTTERS -- COGELOW & PAINTER -- CARVING TOOL SETS -- SELECTED SETS -- MICRO CARVING TOOLS -- TURNING TOOLS & SETS -- GOUGES -- CHISELS -- SCRAPERS -- HEAVY DUTY BOWL TURNING SCRAPERS -- BEADING TOOLS -- PARTING TOOLS -- HSS TURNING TOOLS 1 -- HSS TURNING TOOLS 2 --
HSS TURNING TOOLS 3 -- SUPERTIP 2000 -- KRYO RANGE -- WOODWORKING CHISELS -- CONTACT
©  Copyright Web Technik 2002