 |
| Round
Bar Skew Chisels Developed
specially to allow the blade to move more freely along the
tool rest. Blade length 11½". |
| HS129 |
3/8" |
| HS130 |
½" |
| HS131 |
5/8" |
|
 |
| Round
Edge Skew Chisel - The
rounded smooth edges allow the skew to slide smoothly along
the rest. It has greater mass and stability than oval skews.
Usable blade length 6" |
| HS147 |
½" |
| HS148 |
¾" |
| HS149 |
1" |
|
 |
Modified
Grind Bowl Gouge
The
corners are ground much further back than on a standard bowl gouge,
with the cutting edge nearly blending in with the flute. The increased
length of the cutting edge makes a tool that can take a very large
cut and requires considerable motor power, as well as skill nand
experience on the part of the turner. Not recommended for beginners.
Blade length 10"
| HS129 |
3/8" |
| HS130 |
½" |
| HS131 |
5/8" |
|
 |
Detail
Gouge
Designed
for detail work primarily on spindle work, the shallow flute and
heavy cross section make it stable and easy to control. Ground with
a "fingernail" grind. Useable blade length 7" |
 |
S.
Mortimer Helical Tool
A
¾" twisting
gouge. Is used to cut the trough or hollow when roughing out the
twists on spiral work after the initial saw cuts have been made.
The gouge is designed especially for this type of work.
It is about 4" long, not including the tang with a long hollow
ground bevel and finger nail shape sharpened fully around the leading
edge to the heel of the tool. It should be fitted with a standard
chisel handle.
|
|
Shallow
Gouge
For
roughing down stock or turning large spindles. Designed by
Rude Osolniik. Useable blade length 9".
|
| |
|
 |
Round
Edge Shear Scraper
The
round edges allow smooth tool travel along the tool rest as well
as ease in positioning the tool at the desired shearing angle. Excellent
for improving gouge surfaces and removing small ridges or tom grain.
Usable blade length 6"
|
 |
Ellsworth
Gouge
This
tool was developed in conjunction with David Ellsworth well known
U.S. woodturner. It is made from 16mm roung bar with a 7½"
flute.
The special feature of this gouge is a side grind which enables
roughing and fine cuts can be achieved on bowls.
|
 |
Dovetail
Scraper
This
tool is specially designed for making accurate recesses to accommodate
the jaws of an expanding dovetail chuck.
|
 |
Radius
Edge Shear Scraper
The
radius point provides versatility as the shearing cut can be made
either way depending on grain direction. The round edge allows smooth
travel along the tool rest while the tool is tipped on edge. Tipped
30-45 degrees the shear scraping cut will improve the sruface prior
to standing.
Useable blade length 6½".
|
 |
Beading
Tools
These
tools will produce beads quickly and consistently and are wonderful
for small detail in dense, close grained woods, plastics, bone,
etc. They are sharpened by grinding or honing the bevelled edge
and can be used until the flute is gone. Unhandled. Useable blade
length 5"
| HS140
|
5/16"
Square Stock for 1/16" Bead |
| HS141 |
5/16"
Square Stock for 1/8" Bead |
| HS142 |
5/16"
X ½"
Stock
for 3/16" Bead |
| HS143 |
5/16"
X ½"
Stock
for ¼"
Bead
|
| HS144 |
3/8"
X ½"
Stock
for 5/16" Bead
|
|
 |
Thin
Parting Tools
The 1/16" parting tool is the thinnest standard
parting tool currently available, producing minimal waste when used.
| HS167
|
½"
X 1/16" |
| HS168 |
1"
x 1/16" |
| HS169 |
1½"
x 1/16" |
| HS170 |
2"
x 1/16" |
|
 |
Coving
Tool
This tool makes it possible to cut coves with speed
and consistency. The shearing cut produces a smooth surface and
the flat bevel is easy to sharpen. Can make many sizes of coves.
Useable blade length 7"
|
 |
Captive
Ring Tools
Specifically made for producing rings.
| HS132
|
3/8"
x 1/4" x 6" |
| |
Long
Blade for 1/4" Beads |
| HS133 |
1/2"
x
1/4" x 6" |
| |
Long
Blade for 1/4" Beads |
| HS134 |
5/8"
x
1/4" x 6" |
| |
Long
Blade for 1/2" Beads |
|
 |
Pyramid
Tool
This unique multi-purpose tool is ideal for beginners
and experienced woodturners alike. When used as a skew the problems
of digging are greatly reduced. Suitable for both spindle and face
plate. Able to cut beads and shoulders. |
 |
Allan
Batty Arm Rest
This
tool was developed in conjunction with Allan Batty well known international
woodturner. This additional tool rest is to aid working at the face,
boring, hollow turning and inside screw cutters with chaser. blade
length 8½" |
| |
